Eccentric spacers are used for making fine adjustments to the spacing between the v-wheels on either side of an aluminum extrusion. Adjusting this spacing is key to achieving smooth and wobble-free movement of the gantry across the tracks, the cross-slide across the gantry main beam, and the z-axis up and down the cross-slide.

If the spacing between v-wheels is too little, then the extrusions will not fit between the v-wheels at all or be tough to move. If the spacing is too great, then the connection will be wobbly and loose. Let’s adjust the eccentric spacers throughout FarmBot to be just right.

Fit test

First, see if the extrusion will easily slide in between the v-wheels. It will very likely either be too loose and wobble, or too tight and not fit at all. Take note of which v-wheels need adjustment.

Don't use force

If the wheel spacing is too small, do not force it on. Excessive force can bend a screw or plate, deform or break a wheel, or cause other damage.

gantry wheel plate fit test

Adjust the eccentric spacers

  1. Separate the extrusion and the wheel/plate assembly.
  2. Using the 8mm end of the 5.5mm and 8mm combo wrench, rotate the eccentric spacer that needs adjusting about 1/16 of a turn. Depending on the direction you turn the spacer, and the current orientation of the spacer, the spacing will either increase or decrease. Your goal is to adjust the spacer in the direction you need. Make the spacing smaller if the connection was loose. Make the spacing larger if the extrusion did not fit between the v-wheels or if there was a lot of friction. The side of the eccentric spacer with the 6mm engraving indicates the shortest distance, so moving the text towards the other wheels will decrease the spacing.
  3. Do another fit test.
  4. Repeat the steps above for all eccentric spacers until the connections are smooth and wobble free.

Gantry wheel plates

These eccentric spacers on the gantry wheel plates affect the fit of the gantry on the track extrusions. To set the spacers to the loosest setting, position the 6mm engraving on the spacers facing away from the track extrusions (down).

gantry wheel plate eccentric spacers loosest gantry wheel plate eccentric spacers loosest gantry wheel plate eccentric spacers

Cross-slide

These eccentric spacers on the cross-slide affect the fit of the cross-slide on the gantry main beam. To set the spacers to the loosest setting, position the 6mm engraving on the spacers facing away from the gantry main beam.

cross-slide eccentric spacers loosest cross-slide eccentric spacers loosest cross-slide eccentric spacers

Z-axis

These eccentric spacers on the cross-slide affect the fit of the z-axis in the cross-slide. To set the spacers to the loosest setting, position the 6mm engraving on the spacers facing away from the z-axis extrusion.

z-axis eccentric spacers loosest z-axis eccentric spacers loosest z-axis eccentric spacers

Need just a little more space?

If the fit of the wheels on the extrusion is still too tight after adjusting all of the eccentric spacers to their loosest setting (6mm engraving facing away from the extrusion), you can increase the distance between the two sets of wheels slightly more by adjusting the wheels with standard spacers as well.

Loosen the screws attaching the wheels with standard spacers (non-eccentric) until the wheel assemblies can be moved around in the holes in the plate. Gently nudge the wheel assemblies in the holes so that they are farthest from the extrusion and re-tighten the screws.

The perfect fit

The perfect fit is subjective and you’ll need to play around to get it just right. Here is our best tip: Adjust your wheel spacing so that it is as large as possible without inducing wobbling or rattling. This will ensure you are not over tightening your wheels and risking damage.

You would rather have a wobbly wheel that you can tighten later than damaged components now.

Don’t expect anything to roll like a ball down a hill. A well fitted extrusion/v-wheel connection will have a small amount of friction. Again, just play around with the spacing and use your best judgement.