Genesis Genesis XL
Part Notes Price Cost Qty Subtotal Subtotal Qty Subtotal Subtotal
Belt Clip Belt Clip Rev A --- $3.00 $1.80 6 $18.00 $10.80 6 $18.00 $10.80
35mm Cable Carrier Mount Cable Carrier Mount - 35mm Rev A --- $8.00 $2.00 1 $8.00 $2.00 1 $8.00 $2.00
80mm Cable Carrier Mount Cable Carrier Mount - 80mm Rev A --- $10.00 $2.30 1 $10.00 $2.30 1 $10.00 $2.30
Cross-Slide Plate Genesis Cross-Slide Plate Rev B --- $25.00 $5.80 1 $25.00 $5.80 1 $25.00 $5.80
Left Gantry Corner Bracket Gantry Corner Bracket - Left Rev A --- $30.00 $4.75 1 $30.00 $4.75 1 $30.00 $4.75
Right Gantry Corner Bracket Gantry Corner Bracket - Right Rev A --- $30.00 $4.50 1 $30.00 $4.50 1 $30.00 $4.50
Gantry Joining Bracket Gantry Joining Bracket Rev B --- $35.00 $5.50 0 --- --- 1 $35.00 $5.50
Gantry Wheel Plate Genesis Gantry Wheel Plate Rev B --- $25.00 $4.35 2 $50.00 $8.70 2 $50.00 $8.70
Seed Trough Holder Mount Seed Trough Holder Mount Plate Rev A --- $5.00 $2.75 1 $5.00 $2.75 1 $5.00 $2.75
1-Slot Toolbay Toolbay - 1-Slot Rev A --- $25.00 $6.20 0 --- --- 0 --- ---
3-Slot Toolbay Toolbay - 3-Slot Rev B --- $40.00 $13.90 2 $80.00 $27.80 3 $120.00 $41.70
Track End Plate Track End Plate Rev B --- $12.00 $2.05 4 $48.00 $8.20 4 $48.00 $8.20
Track Joining Plate Track Joining Plate Rev A --- $15.00 $3.10 2 $30.00 $6.20 6 $90.00 $18.60
Z-Axis Hardstop Z-Axis Hardstop Rev A --- $3.00 $1.45 2 $6.00 $2.90 2 $6.00 $2.90
Z-Axis Motor Mount Genesis Z-Axis Motor Mount Rev D --- $20.00 $5.80 1 $20.00 $5.80 1 $20.00 $5.80
TOTAL 25 $360.00 $92.50 31 $495.00 $124.30

Component tests

Size and shape

Test Description Target Tolerance
Overall size Measure the overall length, width, and height with digital calipers. See spec in CAD models. +/- 0.5mm
M3 hole size Measure the diameter of M3 holes using digital calipers. 3.25mm +/- 0.1mm
M5 hole size Measure the diameter of M5 holes using digital calipers. 5.25mm +/- 0.1mm
Eccentric spacer hole size Measure the diameter of eccentric spacer holes using digital calipers. 7.18mm + 0.05mm
Squareness Measure the angle of any 90 degree bends using a digital angle finder. 90 deg +/- 0.5 deg
Deburred Inspect all edges to ensure there are no burrs 0 burrs + 1 minor
+ 0 major

Material and appearance

Test Description Target Tolerance
Material Ensure the material is aluminum and will not rust by holding a magnet to the part. Aluminum (no magnetic attraction) N/A
Sandblasting Inspect for thorough sandblasting coverage. 100% - 1%
Annodization Inspect for thorough annodization coverage. 100% - 1%
Engraving Inspect engravings for aspect ratio, sharpness, and completeness. No stretch or skew.
Sharp edges.
100% complete.		 N/A

Function

Test Description Target Tolerance
M3 screws Insert M3 screws into M3 holes to ensure fit. Screws should be insertable without interference. N/A
M5 screws Insert M5 screws into M5 holes to ensure fit. Screws should be insertable without interference. N/A
Eccentric spacers Insert an eccentric spacer into an eccentric spacer hole to ensure fit. Spacer should fit snug without excessive play. Light tapping with a hammer is permissible.
Nut bars Fasten nut bars of appropriate lengths between holes according to FarmBot system design. Nut bars should be fastenable without screw/hole interference. N/A
Motors Attach motors according to the FarmBot system design. M3 screws should fasten without screw/hole interference. Motor shaft should be centered in hole and make no contact with the plate or bracket. N/A